All Fiber Arts

Rigid Heddle Warping Picture Show - All Fiber Arts

How to warp a rigid heddle loom.  


LINK REPORTHOME FORUMCHATNEWSLETTERCALENDARSITE SEARCHODP SEARCH EMAIL TRAVEL BOOK STORE
Google
 

Link Library
Basketry
Beadwork
Blogs
Bobbin Lace
Bookstore
Classes
Clip Art Graphics
Conferences
Crochet
Cross Stitch
Cultural Travel
Dyes & Colour
eBay Watch
Ethnic Textiles
Felting
Fiber & Yarns
Fun Projects
Galleries/Museums
Guilds
Handspun Yarns
How-To
Instructors
Kits
Knitting
Kumihimo Braiding
Looms
Mailing Lists
Mills
Music
Mythology & Stories
Papermaking
Patterns
Posters
Rug Hooking
Software
Sewing
Small Looms
Spindles & Wheels
Spinning Info
Swedish Weaving
Tapestry Art
Used Equipment
Weaving Info
Yarn Shops
All Links
All Feature Articles


Hemp Yarns

Get Chitika | Premium

Jo posted these pictures and instructions on how to warp a Rigid Heddle loom, to our Forum.
WarpingARigidHeddle1.jpg, 25831 bytes1. tie the end of your warp to the anchor (at a distance that is the lenghth of the warp you want..... NOTE: clamp loom to a stable surface....
WarpingARigidHeddle2.jpg, 25774 bytes2. Sley the slots (only) in the reed - by looping the end of the thread. The slip that loop over the stick attached to the back roller......
WarpingARigidHeddle3.jpg, 25025 bytesRepeat this till the warp is the width you require..... wrap around your anchor and then unwind the yarn to the heddle and pull loop of yarn through the next slot and so on........
WarpingARigidHeddle4.jpg, 18870 bytesThis is what your finished warp will look like.....
WarpingARigidHeddle5.jpg, 35476 bytesAnother view of finished warp....
WarpingARigidHeddle6.jpg, 14939 bytesNow it is the time to cut the warp from your anchor..... It may be best to have someone help you wind the warp as this can help keep even tention and makes it a lot easier for you........
WarpingARigidHeddle7.jpg, 33807 bytesI usually put paper between the layers of wound warp on the back beam...... When you get about 1 foot away from the "fixed" heddle (your heddle should be in the "fixed" position throughout warping).... It is now time to sley the holes..... take the top thread from the slot, starting on the left and put it in the hole to the right......
WarpingARigidHeddle8.jpg, 33040 bytesNow it's time to tie the warp to the front stick that is attched to the front roller/beam..... Please be sure to tie with even tention..... Here is what the warped loom looks like.....
WarpingARigidHeddle9.jpg, 30970 bytesNow it is time to weave...... usually you need to weave what's called a "heading".....just a few wefts till the warp is even (notice the taping at the front - you just want to get past this). When you put in a weft thread into the warp angle it up toward the heddle at about 45 degree angle - this will help to prevent the weaving drawing in at the sides.......
WarpingARigidHeddle10.jpg, 26842 bytesNow beat down that weft - not too hard - if you pack them down too hard your fabric may not drape as nicely. Finally, always wet finish your piece. I wash my woolen item in the washing mashine with hot water but others prefer warm water or even hand washing - this can be an area to experiment as the wet finish can make or break a piece..... Happy Weaving !!
rigidheddle1.jpg, 41083 bytesrigidheddle2.jpg, 36121 bytesrigidheddle3.jpg, 38206 bytes
rigidheddle4.jpg, 31092 bytes rigidheddle5.jpg, 33213 bytesKnee Rugs woven on a Rigid Heddle Loom

Related Resources:

Small Looms


All Fiber Arts - Books
Books

CA
UK

CA
UK

CA
UK

CA
UK

CA
UK

CA
UK
Affiliate Links
Amazon US
Amazon CA
Amazon UK

Sign up for our New Newsletter
Feature Articles  Newsletter
Link Library

All Fiber Arts All Gluten Free All Organic LivingAll Treks.com Paivatar
©2001 Paivi Suomi.